Texas Instruments
画像はイメージの場合もございます。
商品詳細は仕様をご覧ください。
INA205AIPWR
詳細を表示 DataSheets

INA205AIPWR

Basic Information Overview

  • Category: Integrated Circuit (IC)
  • Use: Current Shunt Monitor
  • Characteristics: High accuracy, low offset voltage, wide common-mode voltage range
  • Package: TSSOP-8
  • Essence: Monitors current flowing through a shunt resistor
  • Packaging/Quantity: Tape and Reel, 2500 units per reel

Specifications

  • Supply Voltage Range: 2.7V to 26V
  • Input Common-Mode Voltage Range: -0.3V to +26V
  • Output Voltage Swing: 0V to Vcc - 1.2V
  • Quiescent Current: 60µA
  • Gain Error: ±0.5%
  • Offset Voltage: ±100µV
  • Bandwidth: 500kHz
  • Operating Temperature Range: -40°C to +125°C

Detailed Pin Configuration

  1. IN-: Negative input terminal
  2. IN+: Positive input terminal
  3. REF: Reference voltage input
  4. OUT: Output voltage
  5. GND: Ground
  6. SET: Gain setting pin
  7. NC: No connection
  8. VCC: Supply voltage

Functional Features

  • Measures current by monitoring voltage across a shunt resistor
  • High accuracy and low offset voltage ensure precise current measurement
  • Wide common-mode voltage range allows for versatile applications
  • Adjustable gain setting for flexibility in different current sensing scenarios
  • Rail-to-rail output swing enables compatibility with various signal levels

Advantages

  • High accuracy ensures reliable current monitoring
  • Low offset voltage minimizes measurement errors
  • Wide common-mode voltage range accommodates diverse applications
  • Adjustable gain setting provides flexibility in current sensing
  • Small package size saves board space

Disadvantages

  • Limited bandwidth may restrict use in high-frequency applications
  • Requires an external shunt resistor for current measurement

Working Principles

The INA205AIPWR is a current shunt monitor IC that measures the voltage drop across a shunt resistor to determine the current flowing through it. It utilizes a differential amplifier configuration to amplify the small voltage across the shunt resistor and provide an output voltage proportional to the current. The gain of the amplifier can be adjusted using the SET pin, allowing for customization based on the specific current sensing requirements.

Detailed Application Field Plans

  1. Battery Management Systems: Monitor current in battery charging and discharging circuits.
  2. Power Supplies: Measure current in power supply modules for load monitoring and protection.
  3. Motor Control: Monitor motor currents for precise control and fault detection.
  4. Solar Power Systems: Measure current in solar panels and battery charging circuits.
  5. Industrial Automation: Monitor current in various industrial equipment for process control and safety.

Detailed and Complete Alternative Models

  1. INA206AIPWR: Similar specifications with additional diagnostic features.
  2. INA207AIPWR: Higher bandwidth version with similar accuracy and offset voltage.
  3. INA208AIPWR: Lower quiescent current and wider supply voltage range.

(Note: This entry has a total word count of 446 words)

技術ソリューションにおける INA205AIPWR の適用に関連する 10 件の一般的な質問と回答をリストします。

Sure! Here are 10 common questions and answers related to the application of INA205AIPWR in technical solutions:

  1. Q: What is the INA205AIPWR? A: The INA205AIPWR is a high-side current shunt monitor IC that can accurately measure current flowing through a shunt resistor.

  2. Q: What is the purpose of using the INA205AIPWR in a technical solution? A: The INA205AIPWR is commonly used to monitor and measure current in various applications such as power supplies, motor control, battery management, and industrial automation.

  3. Q: How does the INA205AIPWR work? A: The INA205AIPWR measures the voltage drop across a shunt resistor and converts it into a proportional output voltage, which can be easily measured by a microcontroller or ADC.

  4. Q: What is the maximum current range that the INA205AIPWR can measure? A: The INA205AIPWR can measure currents up to ±2A with a typical accuracy of 0.5%.

  5. Q: Can the INA205AIPWR handle high voltages? A: Yes, the INA205AIPWR can operate at high supply voltages up to 26V, making it suitable for a wide range of applications.

  6. Q: Does the INA205AIPWR require an external shunt resistor? A: Yes, the INA205AIPWR requires an external shunt resistor to accurately measure the current. The value of the shunt resistor depends on the desired current range and sensitivity.

  7. Q: Is the INA205AIPWR compatible with different communication interfaces? A: No, the INA205AIPWR does not have built-in communication interfaces. It provides an analog output voltage that can be easily interfaced with microcontrollers or ADCs.

  8. Q: Can the INA205AIPWR operate in harsh environments? A: Yes, the INA205AIPWR is designed to operate in a wide temperature range (-40°C to +125°C) and is suitable for industrial applications.

  9. Q: Does the INA205AIPWR have any built-in protection features? A: Yes, the INA205AIPWR has built-in overcurrent and overtemperature protection, which helps safeguard the device and the connected circuitry.

  10. Q: Are there any application notes or reference designs available for the INA205AIPWR? A: Yes, Texas Instruments provides application notes and reference designs that can help users understand and implement the INA205AIPWR in their technical solutions effectively.

Please note that these answers are general and may vary depending on specific use cases and requirements.