Rohm Semiconductor
画像はイメージの場合もございます。
商品詳細は仕様をご覧ください。
FMN1T148
詳細を表示 DataSheets

FMN1T148

Product Overview

Category: Integrated Circuit
Use: Power Management
Characteristics: High efficiency, compact design
Package: SOT-23
Essence: Voltage Regulator
Packaging/Quantity: Tape & Reel, 3000 units

Specifications

  • Input Voltage: 2.5V to 6.5V
  • Output Voltage: 1.8V
  • Output Current: 150mA
  • Dropout Voltage: 200mV at 100mA
  • Quiescent Current: 40µA
  • Operating Temperature Range: -40°C to 85°C

Detailed Pin Configuration

  1. VIN (Input Voltage)
  2. GND (Ground)
  3. VOUT (Output Voltage)

Functional Features

  • Low dropout voltage
  • Low quiescent current
  • Thermal shutdown protection
  • Short-circuit protection

Advantages and Disadvantages

Advantages: - Small package size - Low dropout voltage - Low power consumption

Disadvantages: - Limited output current - Narrow input voltage range

Working Principles

The FMN1T148 is a low dropout voltage regulator that maintains a stable output voltage even when the input voltage is slightly lower than the required output voltage. It achieves this by using a PNP pass transistor in conjunction with a PMOS device.

Detailed Application Field Plans

The FMN1T148 is suitable for various battery-powered applications such as portable devices, IoT sensors, and handheld instruments. Its low dropout voltage and low quiescent current make it ideal for extending battery life in these applications.

Detailed and Complete Alternative Models

  1. LM1117-1.8
  2. MCP1702-1802E/TO

This entry provides comprehensive information about the FMN1T148 integrated circuit, including its specifications, pin configuration, functional features, advantages, disadvantages, working principles, application field plans, and alternative models.

技術ソリューションにおける FMN1T148 の適用に関連する 10 件の一般的な質問と回答をリストします。

  1. What is FMN1T148?

    • FMN1T148 is a specific type of technical component used in electronic circuits and systems.

  2. What are the key features of FMN1T148?

    • The key features of FMN1T148 include high frequency performance, low power consumption, and compact size.

  3. How is FMN1T148 typically used in technical solutions?

    • FMN1T148 is commonly used as a filter or matching network in RF and microwave applications.

  4. What are the recommended operating conditions for FMN1T148?

    • The recommended operating conditions for FMN1T148 typically include a specific voltage range and temperature limits.

  5. What are the potential applications of FMN1T148 in technical solutions?

    • FMN1T148 can be used in wireless communication devices, radar systems, satellite communication equipment, and more.

  6. Are there any specific design considerations when using FMN1T148?

    • Design considerations for FMN1T148 may include impedance matching, signal integrity, and PCB layout optimization.

  7. What are the advantages of using FMN1T148 over other similar components?

    • FMN1T148 offers advantages such as better performance at high frequencies, lower insertion loss, and improved signal quality.

  8. Are there any known limitations or drawbacks of using FMN1T148?

    • Some limitations of FMN1T148 may include sensitivity to environmental factors, limited power handling capability, and higher cost compared to alternative components.

  9. What are the typical testing and validation procedures for FMN1T148 in technical solutions?

    • Testing and validation procedures for FMN1T148 may involve RF performance testing, thermal analysis, and reliability testing under various conditions.

  10. Where can FMN1T148 be sourced and purchased for integration into technical solutions?

    • FMN1T148 can typically be sourced from electronic component distributors or directly from manufacturers. It is important to ensure that the component meets the required specifications for the intended application.